出典(authority):フリー百科事典『ウィキペディア（Wikipedia）』「2015/12/28 08:24:26」(JST)
In materials science, quenching, a type of heat treating, is the rapid cooling of a workpiece to obtain certain material properties. It prevents low-temperature processes, such as phase transformations, from occurring by only providing a narrow window of time in which the reaction is both thermodynamically favorable and kinetically accessible. For instance, it can reduce crystallinity and thereby increasing the hardness of both alloys and plastics (produced through polymerization).
In metallurgy, it is most commonly used to harden steel by introducing martensite, in which case the steel must be rapidly cooled through its eutectoid point, the temperature at which austenite becomes unstable. In steel alloyed with metals such as nickel and manganese, the eutectoid temperature becomes much lower, but the kinetic barriers to phase transformation remain the same. This allows quenching to start at a lower temperature, making the process much easier. High speed steel also has added tungsten, which serves to raise kinetic barriers and give the illusion that the material has been cooled more rapidly than it really has. Even cooling such alloys slowly in air has most of the desired effects of quenching.
Extremely rapid cooling can prevent the formation of all crystal structure, resulting in amorphous metal or "metallic glass".
If the percentage of carbon is less than 0.4 percent, quenching is not possible.
Quench hardening is a mechanical process in which steel and cast iron alloys are strengthened and hardened. These metals consist of ferrous metals and alloys. This is done by heating the material to a certain temperature, depending on the material. This produces a harder material by either surface hardening or through-hardening varying on the rate at which the material is cooled. The material is then often tempered to reduce the brittleness that may increase from the quench hardening process. Items that may be quenched include gears, shafts, and wear blocks.
Quenching metals is a progression and the first step is heating, i.e. heating it to the required temperature. Second step is soaking. Soaking can be done by air (air furnace), or a bath or in a vacuum. The soaking time in air furnaces should be 1 to 2 minutes for each millimeter of cross-section. For a bath the time can range a little higher within a vacuum and, soak is generally similar to in air. The recommended time allotment in salt or lead baths is 0 to 6 minutes. Uneven heating or overheating should be avoided at all cost. Most materials are heated from anywhere to 815 to 900 °C (1,500 to 1,650 °F).
The next item on the progression list is the cooling of the part. Water is one of the most efficient quenching media where maximum hardness is acquired, but there is a small chance that it may cause distortion and tiny cracking. When hardness can be sacrificed, whale oil, cottonseed oil and mineral oils are used. These often tend to oxidize and form a sludge, which consequently lowers the efficiency. The quenching velocity (cooling rate) of oil is much less than water. Intermediate rates between water and oil can be obtained with water containing 10-30% UCON from DOW,[clarification needed] a substance with an inverse solubility which therefore deposits on the object to slow the rate of cooling. Quenching can also be accomplished using inert gases. Most commonly, nitrogen is used at pressures greater than atmospheric pressure ranging up to 20 bar absolute. Helium is also used because of its greater thermal capacity than nitrogen. Alternatively argon can be used however its density requires significantly more horsepower to move it and its thermal capacity is less than the alternatives.
To minimize distortion, long cylindrical work pieces are quenched vertically; flat work pieces are quenched on edge; and thick sections should enter the bath first. To prevent steam bubbles the bath is agitated.
High Pressure Gas Quenching (HPGQ) offers far better possibilities of workpiece distortion control by controlling the pressure, wind speed, wind direction as well as the actual gas used.[citation needed]
Before the material is hardened, the microstructure of the material is a pearlite grain structure that is uniform and lamellar. Pearlite is a mixture of ferrite and cementite formed when steel or cast iron are manufactured and cooled at a slow rate. After quench hardening, the microstructure of the material form into martensite as a fine, needle-like grain structure.[1]
Before using this technique it is essential to look up the rate constants for the quenching of the excited states of metal ions.[citation needed]
There are four (4) types of furnaces that are commonly used in quench hardening: salt bath furnace,[2] continuous furnace,[3] box furnace and vacuum furnace. Each is used depending on what other processes or types of quench hardening are being done on the different materials.
When quenching, there are numerous types of media called quenchants. Some of the more common include: air, nitrogen, argon, helium, brine (salt water), oil and water. These media are used to increase the severity of the quench.[4]
| Look up quenching in Wiktionary, the free dictionary. |
全文を閲覧するには購読必要です。 To read the full text you will need to subscribe.
| リンク元 | 「extinction」「消光」「extinguish」「quench」「急冷」 |