出典(authority):フリー百科事典『ウィキペディア（Wikipedia）』「2014/05/15 20:20:20」(JST)
In spectroscopy, the absorbance (also called optical density[2][3]) of a material is a logarithmic ratio of the radiation falling upon a material, to the radiation transmitted through a material.[4][5] Absorbance measurements are often carried out in analytical chemistry.
In physics, the term spectral absorbance is used interchangeably with spectral absorptance or absorptivity. In this case it has a slightly different meaning: the fraction of radiation absorbed at specific wavelengths.
Absorbance is a quantitative measure expressed as a logarithmic ratio between the radiation falling upon a material and the radiation transmitted through a material.
where is the absorbance at a certain wavelength of light (), is the intensity of the radiation (light) that has passed through the material (transmitted radiation), and is the intensity of the radiation before it passes through the material (incident radiation).
Outside the field of analytical chemistry, e.g. when used in biology and the Tunable Diode Laser Absorption Spectroscopy (TDLAS) technique, the absorbance is often defined using the natural logarithm instead of the common logarithm, i.e. as
The term absorption refers to the physical process of absorbing light, while absorbance refers to the mathematical quantity. Also, absorbance does not always measure absorption: if a given sample is, for example, a dispersion, part of the incident light will in fact be scattered by the dispersed particles, and not really absorbed. However, in such cases, it is recommended that the term "attenuance" (formerly called "extinction") be used, which accounts for losses due to scattering and luminescence.[6]
See the Beer-Lambert law for a more complete discussion.
Although absorbance is properly unitless, it is sometimes reported in "Absorbance Units" or AU. However, many people, including scientific researchers, wrongly state the results from absorbance measurement experiments in terms of arbitrary units.[7]
The amount of light transmitted through a material diminishes exponentially as it travels through the material. Since the absorbance of a sample is measured as a logarithm, it is directly proportional to the thickness of the sample and to the concentration of the absorbing material in the sample. Some other measures related to absorption, such as transmittance, are measured as a simple ratio so they vary exponentially with thickness and concentration of the material.
| Absorbance | Transmittance () |
|---|---|
| 0 | 1 |
| 0.1 | 0.79 |
| 0.25 | 0.56 |
| 0.5 | 0.32 |
| 0.75 | 0.18 |
| 0.9 | 0.13 |
| 1 | 0.1 |
| 2 | 0.01 |
| 3 | 0.001 |
Any real measuring instrument has a limited range over which it can accurately measure absorbance. An instrument must be calibrated and checked against known standards if the readings are to be trusted. Many instruments will become non-linear (fail to follow the Beer-Lambert law) starting at approximately 2 AU (~1% Transmission). It is also difficult to accurately measure very small absorbance values (below 10−4) with commercially available instruments for chemical analysis. In such cases, laser-based absorption techniques can be used, since they have demonstrated detection limits that supersede those obtained by conventional non-laser-based instruments by many orders of magnitude (detections have been demonstrated all the way down to 5×10−13). The theoretical best accuracy for most commercially available non-laser-based instruments is in the range near 1 AU. The path length or concentration should then, when possible, be adjusted to achieve readings near this range.
Some filters, notably welding glass, are rated by shade number, which is 7/3 times the absorbance plus one:[8]
or
So, if the filter has 0.1% transmittance (0.001 transmittance, which is 3 absorbance units) the shade number would be 8.
Many similar terms are used to describe concepts relating to absorbance and some terms may have differing interpretation or usage in different disciplines.
Absorptance refers to a directly proportional ratio. Absorptance is the ratio of the radiation absorbed by a surface to that incident upon it. Total absorptance refers to absorptance measured over all wavelengths. Spectral absorptance refers to absorptance measured at a specified wavelengths.[9]
Absorptance is a simple ratio, whereas absorbance is a logarithmic ratio. This difference means that the two different measures are often used for different applications. Color and Vision Research Laboratories, Institute of Ophthalmology, UCL, explains:
Absorbance spectra are typically used to define photopigment spectra because their shape, when normalized (i.e., plotted as a fraction of the maximum absorbance), is independent of pigment optical density (pigment concentration). In contrast, the absorptance spectra, like the spectral sensitivity of the human subject, broadens as the optical density increases.[10]
Same as Absorptance.
In physics, the term spectral absorbance is used interchangeably with absorptivity, meaning the fraction of radiation absorbed at a given wavelength. In chemistry, absorptivity usually refers to Molar absorptivity, which is the constant used in the Beer-Lambert law, , where is the absorbance, is the concentration of the solution, and is the path length.[11]
A mnemonic to remember the difference between absorbance and absorptance is that absorbance has no t, or not t, meaning it measures all that is not transmitted.
全文を閲覧するには購読必要です。 To read the full text you will need to subscribe.
| リンク元 | 「extinction」「吸光度」「OD」「absorbance」「光学密度」 |
| 関連記事 | 「optical」「optic」 |