出典(authority):フリー百科事典『ウィキペディア(Wikipedia)』「2014/01/30 17:57:57」(JST)
Positive feedback is a process in which the effects of a small disturbance on a system include an increase in the magnitude of the perturbation.[1] That is, A produces more of B which in turn produces more of A.[2] In contrast, a system in which the results of a change act to reduce or counteract it has negative feedback.[1][3]
Mathematically, positive feedback is defined as a positive loop gain around a feedback loop.[1][3] That is, positive feedback is in phase with the input, in the sense that it adds to make the input larger.[4][5] Positive feedback tends to cause system instability. When the loop gain is positive and above 1, there will typically be exponential growth, increasing oscillations or divergences from equilibrium.[3] System parameters will typically accelerate towards extreme values, which may damage or destroy the system, or may end with the system latched into a new stable state. Positive feedback may be controlled by signals in the system being filtered, damped, or limited, or it can be cancelled or reduced by adding negative feedback.
Positive feedback is used in digital electronics to force voltages away from intermediate voltages into '0' and '1' states. On the other hand, thermal runaway is a positive feedback that can destroy semiconductor junctions. Positive feedback in chemical reactions can increase the rate of reactions, and in some cases can lead to explosions. Positive feedback in mechanical design causes tipping-point, or 'over-centre', mechanisms to snap into position, for example in switches and locking pliers. Out of control, it can cause bridges to collapse. Positive feedback in economic systems can cause boom-then-bust cycles. A familiar example of positive feedback is the loud squealing or howling sound produced by audio feedback in public address systems: the microphone picks up sound from its own loudspeakers, amplifies it, and sends it through the speakers again.
In feedback loops a chain of cause and effect exists where a state variable of a system has a feedback loop influencing its own rate of change. Such feedback can be direct, or can be via other state variables.[3]
Such systems can give rich qualitative behaviors, but whether the feedback is positive or negative in sign is an extremely important influence on the results.[3]
In positive feedback, the derivative of the variable is positively affected by the variables value, and the opposite is true in negative feedback.[3]
A key feature of positive feedback is thus that small disturbances get bigger. When a change occurs in a system, positive feedback causes further change, in the same direction.
A simple feedback loop is shown in the diagram. If the loop gain AB is positive, then a condition of positive or regenerative feedback exists.
If the functions A and B are linear and AB is smaller than unity, then the overall system gain from the input to output is finite, but can be very large as AB approaches unity.[6] In that case, it can be shown that the overall or "closed loop" gain from input to output is:
When AB > 1, the system is unstable, so does not have a well-defined gain; the gain may be called infinite.
Thus depending on the feedback, state changes can be convergent, or divergent. The result of positive feedback is to augment changes, so that small perturbations may result in big changes.
A system in equilibrium in which there is positive feedback to any change from its current state may be unstable, in which case the equilibrium is said to be in an unstable equilibrium. The magnitude of the forces that act to move such a system away from its equilibrium are an increasing function of the "distance" of the state from the equilibrium.
In the real world, positive feedback loops typically do not cause ever-increasing growth, but are modified by limiting effects of some sort. According to Donella Meadows:
Hysteresis can be generated by positive feedback. When the gain of the feedback loop is above 1, then the output moves away from the input, if it is above the input, then it moves towards the nearest positive limit, if it is below the input then it moves towards the nearest negative limit.
Once it reaches the limit, it will be stable. However if the input goes past the limit,[clarification needed] then the feedback will change sign[dubious – discuss] and the output will move in the opposite direction until it hits the opposite limit. The system therefore shows bistable behaviour.
The terms positive and negative were first applied to feedback before the World War II. The idea of positive feedback was already current in the 1920s with the introduction of the regenerative circuit.[8] Friis & Jensen (1924) described regeneration in a set of electronic amplifiers as a case where the "feed-back" action is positive in contrast to negative feed-back action, which they mention only in passing.[9] Harold Stephen Black's classic 1934 paper first details the use of negative feedback in electronic amplifiers. According to Black:
According to Mindell (2002) confusion in the terms arose shortly after this:
Regenerative circuits were invented and patented in 1914[11] for the amplification and reception of very weak radio signals. Carefully controlled positive feedback around a single transistor amplifier can multiply its gain by 1,000 or more.[12] Therefore a signal can be amplified 20,000 or even 100,000 times in one stage, that would normally have a gain of only 20 to 50. The problem with regenerative amplifiers working at these very high gains is that they easily become unstable and start to oscillate. The radio operator has to be prepared to tweak the amount of feedback fairly continuously for good reception. Modern radio receivers use the superheterodyne design, with many more amplification stages, but much more stable operation and no positive feedback.
The oscillation that can break out in a regenerative radio circuit is used in electronic oscillators. By the use of tuned circuits or a piezoelectric crystal (commonly quartz), the signal that is amplified by the positive feedback remains linear and sinusoidal. There are several designs for such harmonic oscillators, including the Armstrong oscillator, Hartley oscillator, Colpitts oscillator, and the Wien bridge oscillator. They all use positive feedback to create oscillations.[13]
Many electronic circuits, especially amplifiers, incorporate negative feedback. This reduces their gain, but improves their linearity, input impedance, output impedance, and bandwidth, and stabilises all of these parameters, including the closed-loop gain. These parameters also become less dependent on the details of the amplifying device itself, and more dependent on the feedback components, which are less likely to vary with manufacturing tolerance, age and temperature. The difference between positive and negative feedback for AC signals is one of phase: if the signal is fed back out of phase, the feedback is negative and if it is in phase the feedback is positive. One problem for amplifier designers who use negative feedback is that some of the components of the circuit will introduce phase shift in the feedback path. If there is a frequency (usually a high frequency) where the phase shift reaches 180°, then the designer must ensure that the amplifier gain at that frequency is very low (usually by low-pass filtering). If the loop gain (the product of the amplifier gain and the extent of the positive feedback) at any frequency is greater than one, then the amplifier will oscillate at that frequency (Barkhausen stability criterion). Such oscillations are sometimes called parasitic oscillations. An amplifier that is stable in one set of conditions can break into parasitic oscillation in another. This may be due to changes in temperature, supply voltage, adjustment of front-panel controls, or even the proximity of a person or other conductive item. Amplifiers may oscillate gently in ways that are hard to detect without an oscilloscope, or the oscillations may be so extensive that only a very distorted or no required signal at all gets through, or that damage occurs. Low frequency parasitic oscillations have been called 'motorboating' due to the similarity to the sound of a low-revving exhaust note.[14]
Digital electronic circuits are sometimes designed to benefit from positive feedback. Normal logic gates usually rely simply on gain to push digital signal voltages away from intermediate values to the values that are meant to represent boolean '0' and '1'. When an input voltage is expected to vary in an analogue way, but sharp thresholds are required for later digital processing, the Schmitt trigger circuit uses positive feedback to ensure that if the input voltage creeps gently above the threshold, the output is forced smartly and rapidly from one logic state to the other. One of the corollaries of the Schmitt trigger's use of positive feedback is that, should the input voltage move gently down again past the same threshold, the positive feedback will hold the output in the same state with no change. This effect is called hysteresis: the input voltage has to drop past a different, lower threshold to 'un-latch' the output and reset it to its original digital value. By reducing the extent of the positive feedback, the hysteresis-width can be reduced, but it can not entirely be eradicated. The Schmitt trigger is, to some extent, a latching circuit.[15]
An electronic flip-flop, or "latch", or "bistable multivibrator", is a circuit that due to high positive feedback is not stable in a balanced or intermediate state. Such a bistable circuit is the basis of one bit of electronic memory. The flip-flop uses a pair of amplifiers, transistors, or logic gates connected to each other so that positive feedback maintains the state of the circuit in one of two unbalanced stable states after the input signal has been removed, until a suitable alternative signal is applied to change the state.[16] Computer random access memory (RAM) can be made in this way, with one latching circuit for each bit of memory.[17]
Thermal runaway occurs in electronic systems because some aspect of a circuit is allowed to pass more current when it gets hotter, then the hotter it gets, the more current it passes, which heats it some more and so it passes yet more current. The effects are usually catastrophic for the device in question. If devices have to be used near to their maximum power-handling capacity, and thermal runaway is possible or likely under certain conditions, improvements can usually be achieved by careful design.[18]
Audio and video systems can demonstrate positive feedback. If a microphone picks up the amplified sound output of loudspeakers in the same circuit, then howling and screeching sounds of audio feedback (at up to the maximum power capacity of the amplifier) will be heard, as random noise is re-amplified by positive feedback and filtered by the characteristics of the audio system and the room. Microphones are not the only transducers subject to this effect. Record deck pickup cartridges can do the same, usually in the low frequency range below about 100 Hz, manifesting as a low rumble. Jimi Hendrix helped to develop the controlled and musical use of audio feedback in electric guitar playing,[19] and later Brian May was a famous proponent of the technique.[20]
Similarly, if a video camera is pointed at a monitor screen that is displaying the camera's own signal, then repeating patterns can be formed on the screen by positive feedback. This video feedback effect was used in the opening sequences to the first ten series of the television program Doctor Who.
In electrical switches, including bimetallic strip based thermostats, the switch usually has hysteresis in the switching action. In these cases hysteresis is mechanically achieved via positive feedback within a tipping point mechanism. The positive feedback action minimises the length of time arcing occurs for during the switching and also holds the contacts in an open or closed state.[21]
A number of examples of positive feedback systems may be found in physiology.
In most cases, such feedback loops culminate in counter-signals being released that suppress or breaks the loop. Childbirth contractions stop when the baby is out of the mother's body. Chemicals break down the blood clot. Lactation stops when the baby no longer nurses.[22]
Positive feedback is a well studied phenomenon in gene regulation, where it is most often associated with bistability. Positive feedback occurs when a gene activates itself directly or indirectly via a double negative feedback loop. Genetic engineers have constructed and tested simple positive feedback networks in bacteria to demonstrate the concept of bistability.[23] A classic example of positive feedback is the lac operon in E. coli. Positive feedback plays an integral role in cellular differentiation, development, and cancer progression, and therefore, positive feedback in gene regulation can have significant physiological consequences. Random motions in molecular dynamics coupled with positive feedback can trigger interesting effects, such as create population of phenotypically different cells from the same parent cell.[24] This happens because noise can become amplified by positive feedback. Positive feedback can also occur in other forms of cell signaling, such as enzyme kinetics or metabolic pathways.[25]
Positive feedback loops have been used to describe aspects of the dynamics of change in biological evolution. For example, beginning at the macro level, Alfred J. Lotka (1945) argued that the evolution of the species was most essentially a matter of selection that fed back energy flows to capture more and more energy for use by living systems.[26] At the human level, Richard Alexander (1989) proposed that social competition between and within human groups fed back to the selection of intelligence thus constantly producing more and more refined human intelligence.[27] Crespi (2004) discussed several other examples of positive feedback loops in evolution.[28] The analogy of Evolutionary arms races provide further examples of positive feedback in biological systems.[29]
It has been shown that changes in biodiversity through the Phanerozoic correlate much better with hyperbolic model (widely used in demography and macrosociology) than with exponential and logistic models (traditionally used in population biology and extensively applied to fossil biodiversity as well). The latter models imply that changes in diversity are guided by a first-order positive feedback (more ancestors, more descendants) and/or a negative feedback arising from resource limitation. Hyperbolic model implies a second-order positive feedback. The hyperbolic pattern of the world population growth has been demonstrated (see below) to arise from a second-order positive feedback between the population size and the rate of technological growth. The hyperbolic character of biodiversity growth can be similarly accounted for by a positive feedback between the diversity and community structure complexity. It has been suggested that the similarity between the curves of biodiversity and human population probably comes from the fact that both are derived from the interference of the hyperbolic trend (produced by the positive feedback) with cyclical and stochastic dynamics.[30]
A cytokine storm, or hypercytokinemia is a potentially fatal immune reaction consisting of a positive feedback loop between cytokines and immune cells, with highly elevated levels of various cytokines.[31] In normal immune function, positive feedback loops can be utilized to enhance the action of B lymphocytes. When a B cell binds its antibodies to an antigen and becomes activated, it begins releasing antibodies and secreting a complement protein called C3. Both C3 and a B cell's antibodies can bind to a pathogen, and when a B cell has its antibodies bind to a pathogen with C3, it speeds up that B cell's secretion of more antibodies and more C3, thus creating a positive feedback loop. [32]
Winner (1996) described gifted children as driven by positive feedback loops involving setting their own learning course, this feeding back satisfaction, thus further setting their learning goals to higher levels and so on.[33] Winner termed this positive feedback loop as a "rage to master." Vandervert (2009a, 2009b) proposed that the child prodigy can be explained in terms of a positive feedback loop between the output of thinking/performing in working memory, which then is fed to the cerebellum where it is streamlined, and then fed back to working memory thus steadily increasing the quantitative and qualitative output of working memory.[34][35] Vandervert also argued that this working memory/cerebellar positive feedback loop was responsible for language evolution in working memory.
Systemic risk is the risk that an amplification or leverage or positive feedback process is built into a system, this is usually unknown, and under certain conditions this process can amplify exponentially and rapidly lead to destructive or chaotic behavior. A Ponzi scheme is a good example of a positive-feedback system, because its output (profit) is fed back to the input (new investors), causing rapid growth toward collapse. W. Brian Arthur has also studied and written on positive feedback in the economy (e.g. W. Brian Arthur, 1990)[36]
Simple systems that clearly separate the inputs from the outputs are not prone to systemic risk. This risk is more likely as the complexity of the system increases, because it becomes more difficult to see or analyze all the possible combinations of variables in the system even under careful stress testing conditions. The more efficient a complex system is, the more likely it is to be prone to systemic risks, because it takes only a small amount of deviation to disrupt the system. Therefore well-designed complex systems generally have built-in features to avoid this condition, such as a small amount of friction, or resistance, or inertia, or time delay to decouple the outputs from the inputs within the system. These factors amount to an inefficiency, but they are necessary to avoid instabilities.
Agriculture and human population can be considered to be in a positive feedback mode,[37] which means that one drives the other with increasing intensity. It is suggested that this positive feedback system will end sometime with a catastrophe, as modern agriculture is using up all of the easily available phosphate and is resorting to highly efficient monocultures which are more susceptible to systemic risk.
Technological innovation and human population can be similarly considered, and this has been offered as an explanation for the apparent hyperbolic growth of the human population in the past, instead of a simpler exponential growth.[38] It is proposed that the growth rate is accelerating because of second-order positive feedback between population and technology.[39](p133–160) Technological growth increases the carrying capacity of land for people, which leads to more population, and so more potential inventors in further technological growth.[39](p146)
Gunnar Myrdal described a vicious circle of increasing inequalities, and poverty, which is known as "circular cumulative causation".[40]
Drought intensifies through positive feedback. A lack of rain decreases soil moisture, which kills plants and/or causes them to release less water through transpiration. Both factors limit evapotranspiration, the process by which water vapor is added to the atmosphere from the surface, and add dry dust to the atmosphere, which absorbs water. Less water vapor means both low dew point temperatures and more efficient daytime heating, decreasing the chances of humidity in the atmosphere leading to cloud formation. Lastly, without clouds, there cannot be rain, and the loop is complete.[citation needed]
Climate "forcings" may push a climate system in the direction of warming or cooling,[41] for example, increased atmospheric concentrations of greenhouse gases cause warming at the surface. Forcings are external to the climate system and feedbacks are internal processes of the system. Some feedback mechanisms act in relative isolation to the rest of the climate system while others are tightly coupled.[42] Forcings, feedbacks and the dynamics of the climate system determine how much and how fast the climate changes. The main positive feedback in global warming is the tendency of warming to increase the amount of water vapor in the atmosphere, which in turn leads to further warming.[43] The main negative feedback comes from the Stefan–Boltzmann law, the amount of heat radiated from the Earth into space is proportional to the fourth power of the temperature of Earth's surface and atmosphere.
Other examples of positive feedback subsystems in climatology include:
The Intergovernmental Panel on Climate Change (IPCC) Fourth Assessment Report states that "Anthropogenic warming could lead to some effects that are abrupt or irreversible, depending upon the rate and magnitude of the climate change."[44]
A self-fulfilling prophecy is a social positive feedback loop between beliefs and behavior: if enough people believe that something is true, their behavior can make it true, and observations of their behavior may in turn increase belief. A classic example is a bank run.
Another sociological example of positive feedback is the network effect. When more people are encouraged to join a network this increases the reach of the network therefore the network expands ever more quickly. A viral video is an example of the network effect in which links to a popular video are shared and redistributed, ensuring that more people see the video and then re-publish the links. This is the basis for many social phenomena, including Ponzi schemes and chain letters. In many cases population size is the limiting factor to the feedback effect.
Internet recommendation systems are expected to increase the diversity of what we see and do online. They help us discover new content and websites among myriad choices. Some recommendation systems, however, unintentionally do the opposite. Because some recommendation systems (i.e. certain collaborative filters) recommend products based on past sales or ratings, they cannot usually recommend products with limited historical data. This can create positive feedback: a rich-get-richer effect for popular products. This bias toward popularity can prevent what are otherwise better recommendations for that user's preferences. A Wharton study details this phenomenon along with several ideas that may promote diversity. [45]
If a chemical reaction causes the release of heat, and the reaction itself happens faster at higher temperatures, then there is a high likelihood of positive feedback. If the heat produced is not removed from the reactants fast enough, thermal runaway can occur and very quickly lead to a chemical explosion.
全文を閲覧するには購読必要です。 To read the full text you will need to subscribe.
リンク元 | 「ポジティブフィードバック」「正のフィードパック」 |
拡張検索 | 「positive-feedback loop」 |
関連記事 | 「positive」「feedback」 |
.