出典(authority):フリー百科事典『ウィキペディア(Wikipedia)』「2016/05/14 07:21:23」(JST)
In mathematics, the slope or gradient of a line is a number that describes both the direction and the steepness of the line.[1] Slope is often denoted by the letter m; there is no clear answer to the question why the letter m is used for slope, but it might be from the "m for multiple" in the equation of a straight line "y = mx + c".[2]
Slope is calculated by finding the ratio of the "vertical change" to the "horizontal change" between (any) two distinct points on a line. Sometimes the ratio is expressed as a quotient ("rise over run"), giving the same number for every two distinct points on the same line. A line that is decreasing has a negative "rise". The line may be practical - as set by a road surveyor, or in a diagram that models a road or a roof either as a description or as a plan.
The rise of a road between two points is the difference between the altitude of the road at those two points, say y1 and y2, or in other words, the rise is (y2 − y1) = Δy. For relatively short distances - where the earth's curvature may be neglected, the run is the difference in distance from a fixed point measured along a level, horizontal line, or in other words, the run is (x2 − x1) = Δx. Here the slope of the road between the two points is simply described as the ratio of the altitude change to the horizontal distance between any two points on the line.
In mathematical language, the slope m of the line is
The concept of slope applies directly to grades or gradients in geography and civil engineering. Through trigonometry, the grade m of a road is related to its angle of incline θ by the tangent function
Thus, a 45° rising line has a slope of +1 and a 45° falling line has a slope of −1.
As a generalization of this practical description, the mathematics of differential calculus defines the slope of a curve at a point as the slope of the tangent line at that point. When the curve given by a series of points in a diagram or in a list of the coordinates of points, the slope may be calculated not at a point but between any two given points. When the curve is given as a continuous function, perhaps as an algebraic formula, then the differential calculus provides rules giving a formula for the slope of the curve at any point in the middle of the curve.
This generalization of the concept of slope allows very complex constructions to be planned and built that go well beyond static structures that are either horizontals or verticals, but can change in time, move in curves, and change depending on the rate of change of other factors. Thereby, the simple idea of slope becomes one of the main basis of the modern world in terms of both technology and the built environment.
The slope of a line in the plane containing the x and y axes is generally represented by the letter m, and is defined as the change in the y coordinate divided by the corresponding change in the x coordinate, between two distinct points on the line. This is described by the following equation:
(The Greek letter delta, Δ, is commonly used in mathematics to mean "difference" or "change".)
Given two points (x1,y1) and (x2,y2), the change in x from one to the other is x2 − x1 (run), while the change in y is y2 − y1 (rise). Substituting both quantities into the above equation generates the formula:
The formula fails for a vertical line, parallel to the y axis (see Division by zero), where the slope can be taken as infinite, so the slope of a vertical line is considered undefined.
Suppose a line runs through two points: P = (1, 2) and Q = (13, 8). By dividing the difference in y-coordinates by the difference in x-coordinates, one can obtain the slope of the line:
As another example, consider a line which runs through the points (4, 15) and (3, 21). Then, the slope of the line is
For example, consider a line running through the points (2,8) and (3,20). This line has a slope, m, of
Consider the two lines: y = -3x + 1 and y = -3 x - 2. Both lines have slope m = -3. They are not the same line. So they are parallel lines.
Consider the two lines y = -3x + 1 and y = x/3 - 2. The slope of the first line is m1 = -3. The slope of the second line is m2 = 1/3. The product of these two slopes is -1. So these two lines are perpendicular.
There are two common ways to describe the steepness of a road or railroad. One is by the angle between 0° and 90° (in degrees), and the other is by the slope in a percentage. See also steep grade railway and rack railway.
The formulae for converting a slope given as a percentage into an angle in degrees and vice versa are:
where angle is in degrees and the trigonometric functions operate in degrees. For example, a slope of 100% or 1000‰ is an angle of 45°.
A third way is to give one unit of rise in say 10, 20, 50 or 100 horizontal units, e.g. 1:10. 1:20, 1:50 or 1:100 (or "1 in 10", "1 in 20" etc.) Note that 1:10 is steeper than 1:20. For example, steepness of 20% means 1:5 or an incline with angle 11,3°.
Slope warning sign in the Netherlands
Slope warning sign in Poland
A 1371-meter distance of a railroad with a 20‰ slope. Czech Republic
Steam-age railway gradient post indicating a slope in both directions at Meols railway station, United Kingdom
The concept of a slope is central to differential calculus. For non-linear functions, the rate of change varies along the curve. The derivative of the function at a point is the slope of the line tangent to the curve at the point, and is thus equal to the rate of change of the function at that point.
If we let Δx and Δy be the distances (along the x and y axes, respectively) between two points on a curve, then the slope given by the above definition,
is the slope of a secant line to the curve. For a line, the secant between any two points is the line itself, but this is not the case for any other type of curve.
For example, the slope of the secant intersecting y = x2 at (0,0) and (3,9) is 3. (The slope of the tangent at x = 3⁄2 is also 3—a consequence of the mean value theorem.)
By moving the two points closer together so that Δy and Δx decrease, the secant line more closely approximates a tangent line to the curve, and as such the slope of the secant approaches that of the tangent. Using differential calculus, we can determine the limit, or the value that Δy/Δx approaches as Δy and Δx get closer to zero; it follows that this limit is the exact slope of the tangent. If y is dependent on x, then it is sufficient to take the limit where only Δx approaches zero. Therefore, the slope of the tangent is the limit of Δy/Δx as Δx approaches zero, or dy/dx. We call this limit the derivative.
Its value at a point on the function gives us the slope of the tangent at that point. For example, let y=x2. A point on this function is (-2,4). The derivative of this function is dy/dx=2x. So the slope of the line tangent to y at (-2,4) is 2·(-2) = -4. The equation of this tangent line is: y-4=(-4)(x-(-2)) or y = -4x - 4.
The concept of slope can be generalized to functions of more than one variable and is more often referred to as gradient.
Look up slope in Wiktionary, the free dictionary. |
全文を閲覧するには購読必要です。 To read the full text you will need to subscribe.
リンク元 | 「ramp」「gradient」「勾配」 |
.