出典(authority):フリー百科事典『ウィキペディア（Wikipedia）』「2016/03/23 23:22:28」(JST)
A radial tire (more properly, a radial-ply tire) is a particular design of vehicular tire. In this design, the cord plies are arranged at 90 degrees to the direction of travel, or radially (from the center of the tire).
The first radial tire designs were patented in 1915 by Arthur W. Savage, a tire manufacturer (1915-1919), and inventor in San Diego, CA.[1][2] Savage's patents expired in 1949.
Michelin in France designed, developed, patented, and commercialized the radial tire.[3] There is no evidence that Michelin had knowledge of Arthur Savage's earlier work. The first Michelin X radial tire for cars was developed in 1946 by Michelin researcher Marius Mignol. Michelin owned the leading automaker Citroën, so it was quickly able to introduce its new design, including on the new 1948 Citroën 2CV model.[4] In 1952, Michelin developed a radial truck tire.[5]
Because of its significant advantages,[6] this technology spread quickly in Europe and Asia in the 1950s and 1960s.[7] [8]
In 1968, Consumer Reports, an influential American magazine, acknowledged the superiority of the radial tire design, documenting its longer tread life, better steering characteristics, and less rolling resistance, which increases gas mileage.[9][10]
In 1970, Ford Motor Company produced the first American-made vehicle with radial tires as standard equipment, the Lincoln Continental Mark III.[11]
In 1974, Leopoldo Pirelli created the wide radial tyre in Italy, upon a request from the Lancia rally racing team for a tyre strong sufficient to withstand the power of the new Lancia Stratos. At that time, racing tyres were either slick tyres made with the cross ply technique (very wide tyres with a reduced sidewall height), or radial tyres, which were too narrow to withstand the Stratos' power and did not provide enough grip. Both were unusable for the Lancia Stratos, as the radials were destroyed within 10 km, and the slicks too stiff. Lancia asked Pirelli for a solution, and in the succeeding year Pirelli also made a wide tyre with a reduced sidewall height like a slick, but with a radial structure.
Radial technology is now the standard design for essentially all automotive tires.[12]
Bias tires are still popular on trailers due to their weight carrying ability and resistance to swaying when towed.[13] Bias tires also remain popular for aircraft tires as they afford more stability at higher speeds and have stronger sidewalls.[14]
A series of plies of cord reinforces a tire. Without this, a tire would be flexible and weak. The network of cords that gives the tire strength and shape is called the carcass. Since the 1960s, all common tires have a carcass of cords of polyester, steel, or other textile materials, inlaid with several layers of rubber.
In the past, the fabric was built up on a flat steel drum, with the cords at angles of about +60 and −60 degrees from the direction of travel, so they criss-crossed over each other. They were called cross-ply or bias ply tires. The plies were turned up around the steel wire beads and the combined tread/sidewall applied. The green (uncured) tire was loaded over a curing bladder and shaped into the mold. This shaping process caused the cords in the tire to assume an S-shape from bead to bead. The angle under the tread, the crown angle, stretched down to about 36 degrees. In the sidewall region the angle was 45 degrees, and in the bead it remained at 60 degrees. The low crown angle gave rigidity to support the tread and the high sidewall angle gave comfort. To increase strength, the manufacturer would increase the number of plies, and the heat buildup in the tire.[15]
By comparison, radial tires lay all of the cord plies at 90 degrees to the direction of travel (that is, across the tire from lip to lip). This design avoids having the plies rub against each other as the tire flexes, reducing the tire's rolling friction. This allows vehicles with radial tires to achieve better fuel economy than with bias-ply tires. It also accounts for the slightly "low on air" (bulging) look that radial tire sidewalls have, especially when compared to bias-ply tires.
With only radial cords, a radial tire would not be sufficiently rigid at the contact with the ground. To add further stiffness, the entire tire is surrounded by additional belts oriented closer to the direction of travel, but usually at some "spiral" angle. These belts can be made of steel (hence the term steel-belted radial), polyester, or Aramid fibers such as Twaron or Kevlar.
In this way, low radial tires separate the tire carcass into two separate systems:
Each system can then be individually optimized for best performance.
Radial tires have different characteristics of springiness from those of bias-ply tires, and a different degree of slip while steering. Motorists were not accustomed to the feel, hence the suspension systems of cars had to be modified. Ford Motor Company engineer Jack Bajer experimented in the 1960s on a Ford Falcon, by giving it less tight steering, and adding both isolators to the drive shaft and bushings to the suspension, the latter being to absorb the thump of riding over asphalt expansion joints in a concrete roadway. Cars could now be made lighter because they would not have to make up for the deficiencies of bias-ply tires.[16]
Radial tires have occasionally found application on bicycles, used on the 1980s Miyata touring bicycle; models 1000 and 610,[17] and more recently in 2009 on the Maxxis Radiale.[18] Panaracer radial tires were also standard on the Jamis Gentry model bicycle in 1985.
The steel wires in radial tires become magnetic with use, so as they rotate, an alternating magnetic field is created. It is quite measurable with an EMF meter close to the wheel well when the wheel is rotating and is rich in harmonics up to several hundred hertz.[2]
|
||||||||||||||||||||||
全文を閲覧するには購読必要です。 To read the full text you will need to subscribe.
| 関連記事 | 「radial」「p」「tir」「ply」 |