vt.

～に油を差す、～に潤滑剤を差す

goblet cells which produce acid glucoproteins that protect and lubricate the lining of the intestine.

vi.

潤滑剤の用をする。潤滑剤を差す

関: lubricant, lubrication

WordNet

have lubricating properties; "the liquid in this can lubricates well"
make slippery or smooth through the application of a lubricant; "lubricate the key"
apply a lubricant to; "lubricate my car" (同)lube
the condition of having been made smooth or slippery by the application of a lubricant
an application of a lubricant to something
a substance capable of reducing friction by making surfaces smooth or slippery (同)lubricator, lubricating substance, lube
not lubricated (同)ungreased
smeared with oil or grease to reduce friction (同)greased

PrepTutorEJDIC

(摩擦を減らすために)〈機械など〉‘に'潤滑油をさす(塗る)〈皮膚など〉‘を'滑らかにする / 潤滑油として役立つ
滑らかにすること;(摩擦を減らすための)注油,給油
滑らかにするもの,潤滑剤,潤滑油

Wikipedia preview

出典(authority):フリー百科事典『ウィキペディア（Wikipedia）』「2016/10/13 16:21:43」(JST)

wiki en

[Wiki en表示]

Lubrication of the ship steam engine crankshaft. The two bottles of lubricant are attached to the piston and move while the engine is operating.

Lubrication is the process or technique employed to reduce friction between, and wear of one or both, surfaces in proximity and moving relative to each other, by interposing a substance called a lubricant in between them. The lubricant can be a solid, (e.g. Molybdenum disulfide MoS₂)^[1] a solid/liquid dispersion, a liquid such as oil or water, a liquid-liquid dispersion (a grease) or a gas.

With fluid lubricants the applied load is either carried by pressure generated within the liquid due to the frictional viscous resistance to motion of the lubricating fluid between the surfaces, or by the liquid being pumped under pressure between the surfaces.

Lubrication can also describe the phenomenon where reduction of friction occurs unintentionally, which can be hazardous such as hydroplaning on a road.

The science of friction, lubrication and wear is called tribology.

Adequate lubrication allows smooth continuous operation of equipment, reduces the rate of wear, and prevents excessive stresses or seizures at bearings. When lubrication breaks down, components can rub destructively against each other, causing heat, local welding, destructive damage and failure.

The regimes of lubrication

As the load increases on the contacting surfaces three distinct situations can be observed with respect to the mode of lubrication, which are called regimes of lubrication:

Fluid film lubrication is the lubrication regime in which, through viscous forces, the load is fully supported by the lubricant within the space or gap between the parts in motion relative to one another object (the lubricated conjunction) and solid–solid contact is avoided.^[2]
- Hydrostatic lubrication is when an external pressure is applied to the lubricant in the bearing, to maintain the fluid lubricant film where it would otherwise be squeezed out.
- Hydrodynamic lubrication is where the motion of the contacting surfaces, and the exact design of the bearing is used to pump lubricant around the bearing to maintain the lubricating film. This design of bearing may wear when started, stopped or reversed, as the lubricant film breaks down.
Elastohydrodynamic lubrication: Mostly for nonconforming surfaces or higher load conditions, the bodies suffer elastic strains at the contact. Such strain creates a load-bearing area, which provides an almost parallel gap for the fluid to flow through. Much as in hydrodynamic lubrication, the motion of the contacting bodies generates a flow induced pressure, which acts as the bearing force over the contact area. In such high pressure regimes, the viscosity of the fluid may rise considerably. At full film elastohydrodynamic lubrication the generated lubricant film completely separates the surfaces. Contact between raised solid features, or asperities, can occur, leading to a mixed-lubrication or boundary lubrication regime.
Boundary lubrication (also called boundary film lubrication): The hydrodynamic effects are negligible. The bodies come into closer contact at their asperities; the heat developed by the local pressures causes a condition which is called stick-slip and some asperities break off. At the elevated temperature and pressure conditions chemically reactive constituents of the lubricant react with the contact surface forming a highly resistant tenacious layer, or film on the moving solid surfaces (boundary film) which is capable of supporting the load and major wear or breakdown is avoided. Boundary lubrication is also defined as that regime in which the load is carried by the surface asperities rather than by the lubricant.^[3]
Mixed lubrication: This regime is in between the full film elastohydrodynamic and boundary lubrication regimes. The generated lubricant film is not enough to separate the bodies completely, but hydrodynamic effects are considerable.^[4]

Besides supporting the load the lubricant may have to perform other functions as well, for instance it may cool the contact areas and remove wear products. While carrying out these functions the lubricant is constantly replaced from the contact areas either by the relative movement (hydrodynamics) or by externally induced forces.

Lubrication is required for correct operation of mechanical systems pistons, pumps, cams, bearings, turbines, cutting tools etc. where without lubrication the pressure between the surfaces in close proximity would generate enough heat for rapid surface damage which in a coarsened condition may literally weld the surfaces together, causing seizure.

In some applications, such as piston engines, the film between the piston and the cylinder wall also seals the combustion chamber, preventing combustion gases from escaping into the crankcase.

References

Lubrication Science in Persian

^ http://www.engineersedge.com/lubrication/applications_solid_lubrication.htm – 14k
^ San Andrés. L. "Introduction to pump rotordynamics, Part i. Introduction to hydrodynamic lubrication". ("MEEN626 Lubrication Theory Class:Syllabus FALL2006"). [1] (11 Dec 2007)
^ Bosman R. and Schipper D.J. Microscopic Mild Wear in the Boundary Lubrication regime. Laboratory for Surface Technology and Tribology, Faculty of Engineering Technology, University of Twente, P.O. Box 217, NL 7500 AE Enschede, The Netherlands.
^ Akchurin, Aydar; Bosman, Rob; Lugt, Piet M.; Drogen, Mark van (2015-05-31). "On a Model for the Prediction of the Friction Coefficient in Mixed Lubrication Based on a Load-Sharing Concept with Measured Surface Roughness". Tribology Letters. 59 (1): 19. doi:10.1007/s11249-015-0536-z. ISSN 1023-8883.

External links

Different Lubrication Techniques used in Oil & Gas machinery
Machinery Lubrication magazine
International Council for Machinery Lubrication
Engineers Edge
Lubrication Forum
Lubrication and greasing: working principle

UpToDate Contents

全文を閲覧するには購読必要です。 To read the full text you will need to subscribe.

1. 指輪の除去手技 ring removal techniques
2. 気道マネージメントが困難な小児に対する緊急救命装置 emergency rescue devices for difficult pediatric airway management
3. 気管内挿管が困難な小児用のデバイス devices for difficult endotracheal intubation in children
4. 成人への麻酔導入時の気道確保・管理に用いるビデオ喉頭鏡とオプティカルスタイレット video laryngoscopes and optical stylets for airway management for anesthesia in adults
5. 萎縮性副鼻腔炎 atrophic rhinosinusitis

English Journal

Conjunctival Goblet Cell Function: Effect of Contact Lens Wear and Cytokines.

García-Posadas L1, Contreras-Ruiz L, Soriano-Romaní L, Dartt DA, Diebold Y.
Eye & contact lens.Eye Contact Lens.2015 May 19. [Epub ahead of print]
This review focuses on conjunctival goblet cells and their essential function in the maintenance of eye health. The main function of goblet cells is to produce and secrete mucins that lubricate the ocular surface. An excess or a defect in those mucins leads to several alterations that makes goblet c
PMID 26067396

[Anaesthetic management in a paediatric patient with a difficult airway due to epidermolysis bullosa dystrophica].

Blázquez Gómez E1, Garcés Aletá A2, Monclus Diaz E2, Manen Berga F2, García-Aparicio L3, Ontanilla López A4.
Revista española de anestesiología y reanimación.Rev Esp Anestesiol Reanim.2015 May;62(5):280-4. doi: 10.1016/j.redar.2014.08.003. Epub 2014 Dec 11.
Dystrophic epidermolysis bullosa (DEB) is a rare inherited disorder characterized by blistering after minimal trauma. These blisters tend to form dystrophic scars, leading to limiting and life-threatening sequelae. The anaesthetic management of patients with DEB is a challenge, even for the most exp
PMID 25497148

Sexual differences in the sialomes of the zebra tick, Rhipicephalus pulchellus.

Tan AW1, Francischetti IM2, Slovak M3, Kini RM4, Ribeiro JM5.
Journal of proteomics.J Proteomics.2015 Mar 18;117:120-44. doi: 10.1016/j.jprot.2014.12.014. Epub 2015 Jan 7.
Ticks rely exclusively on vertebrate blood for their survival. During feeding ticks inject into their hosts a sophisticated salivary potion that overcomes host hemostasis and adverse inflammatory responses. These mediators may also enhance pathogen transmission. Knowledge of the tick salivary protei
PMID 25576852

Roles and regulation of the mucus barrier in the gut.

Cornick S1, Tawiah A1, Chadee K1.
Tissue barriers.Tissue Barriers.2015 Apr 3;3(1-2):e982426. doi: 10.4161/21688370.2014.982426. eCollection 2015.
The gastrointestinal tract is coated by a thick layer of mucus that forms the front line of innate host defense. Mucus consists of high molecular weight glycoproteins called mucins that are synthesized and secreted by goblet cells and functions primarily to lubricate the epithelium and protect it fr
PMID 25838985

Japanese Journal

水潤滑式オイルフリーの未知なる可能性を追求 : 高効率圧縮機構「Zスクリュー」 (特集コンプレッサの最新動向(1))

油空圧技術 55(10), 27-30, 2016-10
NAID 40020956211

J2210201 表面テクスチャを付与した金型によるチタンのねじ転造 : 有限要素法による摩擦特性の検討

年次大会 : Mechanical Engineering Congress, Japan 2015, "J2210201-1"-"J2210201-3", 2015-09-13
NAID 110010049254

TuA-2-3 Experimental and Numerical Investigation of Hydrocarbon Transfer Mechanism at the Head-Disk Interface

Proceedings of ... JSME-IIP/ASME-ISPS Joint Conference on Micromechatronics for Information and Precision Equipment : IIP/ISPS joint MIPE 2015, "TuA-2-3-1"-"TuA-2-3-3", 2015-06-14
NAID 110010044081