lubricator

　

PrepTutorEJDIC

1. 滑らかにする人(もの);潤滑装置,注油器

Wikipedia preview

出典(authority):フリー百科事典『ウィキペディア（Wikipedia）』「2017/05/09 01:23:26」(JST)

wiki en

[Wiki en表示]

This article is about industrial lubricants. For other uses, see Lubricant (disambiguation).

A lubricant is an organic substance introduced to reduce friction between surfaces in mutual contact, which ultimately reduces the heat generated when the surfaces move. It may also have the function of transmitting forces, transporting foreign particles, or heating or cooling the surfaces. The property of reducing friction is known as lubricity.

In addition to industrial applications, lubricants are used for many other purposes. Other uses include cooking (oils and fats in use in frying pans, in baking to prevent food sticking), bio-medical applications on humans (e.g. lubricants for artificial joints), ultrasound examination, medical examinations, and the use of personal lubricant for sexual purposes.

History

Lubicants have been in some use for thousands of years. Calcium soaps have been identified on the axles of chariots dated to 1400 BC. Building stones were slid on oil-impregrated lumber in the time of the pyramids. In the Roman era, lubricants were based on olive oil and rapeseed oil, and well as animal fats. The growth of lubrication accelerated in the Industrial Revolution with the accompanying use of metal-based machinery. Relying initially on natural oils, needs for such machinery shifted toward petroleum-based materials early in the 1900s. A breakthrough came with the development of vacuum distillation of petroleum, as described by the Vacuum Oil Company. This technology allowed the purification of very nonvolatile substances, which are common in many lubricants.

Properties

A good lubricant generally possesses the following characteristics:

• high boiling point and low freezing point (in order to stay liquid within a wide range of temperature)
• high viscosity index
• thermal stability
• hydraulic stability
• demulsibility
• corrosion prevention
• high resistance to oxidation.

Formulation

Typically lubricants contain 90% base oil (most often petroleum fractions, called mineral oils) and less than 10% additives. Vegetable oils or synthetic liquids such as hydrogenated polyolefins, esters, silicones, fluorocarbons and many others are sometimes used as base oils. Additives deliver reduced friction and wear, increased viscosity, improved viscosity index, resistance to corrosion and oxidation, aging or contamination, etc.

Non-liquid lubricants include grease, powders (dry graphite, PTFE, molybdenum disulphide, tungsten disulphide, etc.), PTFE tape used in plumbing, air cushion and others. Dry lubricants such as graphite, molybdenum disulphide and tungsten disulphide also offer lubrication at temperatures (up to 350 °C) higher than liquid and oil-based lubricants are able to operate. Limited interest has been shown in low friction properties of compacted oxide glaze layers formed at several hundred degrees Celsius in metallic sliding systems, however, practical use is still many years away due to their physically unstable nature.

Additives

Main article: Oil additive

A large number of additives are used to impart performance characteristics to the lubricants. Typical lubicants contain one or more. Automotive lubricants contain as many as ten additives, comprising 20% of the lube. The main families of additives are:

• Pour point depressants are compounds that prevent crystallization of waxes. Long chain alkylbenzenes adhere to small crystallites of wax, preventing crystal growth.
• Anti-foaming agents are typically silicone, which lower surface tension.
• Viscosity index improvers (VI improvers) are compounds that allow lubricants to remain viscous at higher temperatures. Typical improvers are polyacrylates and butadiene.
• Antioxidants suppress the rate of oxidative degradation of the hydrocarbons that comprise the lubricants. At low temperatures, free radical inhibitors such as hindered phenols are used, e.g. butylated hydroxytoluene. At temperatures > 90 ºC, where the metals catalyze the oxidation process, dithiophosphates are more useful. In the latter application the additives are called metal deactivators.
• Detergents
• Corrosion inhibitors, rust inhibitors are usually alkaline materials, such as alkylsulfonate salts, that absorb acids that would corrode metal parts.
• Anti-wear additives form films on metal parts, suppressing wear. They come in two classes depending on the strength with which they bind to the surface. Fats and fatty acids are employed at milder conditions. For more forcing (hotter) conditions, phosphate esters and zinc dithiophosphates are employed.
• Extreme pressure (antiscuffing) additives form protective films on sliding metal parts. These agents are often sulfur compounds, such as dithiophosphates.

styrene]] copolymers, which adopt a coiled structures at low temperatures and extend in length at higher temperatures, thereby increasing their radius of gyration.

• Demulsifying/Emulsifying

Types of lubricants

In 1999, an estimated 37,300,000 tons of lubricants were consumed worldwide. Automotive applications dominate, but other industrial, marine, and metal working applications are also big consumers of lubricants. Although air and other gas-based lubricants are known (e.g., in fluid bearings), liquid and solid lubricants dominate the market, especially the former.

Lubricants are generally composed of a majority of base oil plus a variety of additives to impart desirable characteristics. Although generally lubricants are based on one type of base oil, mixtures of the base oils also are used to meet performance requirements.

Base oil groups

Mineral oil term is used to encompass lubricating base oil derived from crude oil. The American Petroleum Institute (API) designates several types of lubricant base oil:

• Group I – Saturates < 90% and/or sulfur > 0.03%, and Society of Automotive Engineers (SAE) viscosity index (VI) of 80 to 120

Manufactured by solvent extraction, solvent or catalytic dewaxing, and hydro-finishing processes. Common Group I base oil are 150SN (solvent neutral), 500SN, and 150BS (brightstock)

• Group II – Saturates > 90% and sulfur < 0.03%, and SAE viscosity index of 80 to 120

Manufactured by hydrocracking and solvent or catalytic dewaxing processes. Group II base oil has superior anti-oxidation properties since virtually all hydrocarbon molecules are saturated. It has water-white color.

• Group III – Saturates > 90%, sulfur < 0.03%, and SAE viscosity index over 120

Manufactured by special processes such as isohydromerization. Can be manufactured from base oil or slax wax from dewaxing process.

• Group IV 3 b– Polyalphaolefins (PAO)
• Group V – All others not included above such as naphthenics, PAG, l 80esters.

The lubricant industry commonly extends this group terminology to include:

• Group I+ with a viscosity index of 103–108
• Group II+ with a viscosity index of 113–119
• Group III+ with a viscosity index of at least 140

Can also be classified into three categories depending on the prevailing compositions:

• Paraffinic
• Naphthenic
• Aromatic9

Lubricants for internal combustion engines contain additives to reduce oxidation and improve lubrication. The main constituent of such lubricant product is called the base oil, base stock. While it is advantageous to have a high-grade base oil in a lubricant, proper selection of the lubricant additives is equally as important. Thus some poorly selected formulation of PAO lubricant may not last as long as more expensive formulation of Group III+ lubricant.

Synthetic oils

Petroleum-derived lubricant can also be produced using synthetic hydrocarbons (derived ultimately from petroleum). These include:

• Polyalpha-olefin (PAO)
• Synthetic esters
• Polyalkylene glycols (PAG)
• Phosphate esters
• Alkylated naphthalenes (AN)
• Silicate esters
• Ionic fluids
• Multiply alkylated cyclopentanes (MAC)

Solid lubricants

Main article: Dry lubricant

PTFE: polytetrafluoroethylene (PTFE) is typically used as a coating layer on, for example, cooking utensils to provide a non-stick surface. Its usable temperature range up to 350 °C and chemical inertness make it a useful additive in special greases. Under extreme pressures, PTFE powder or solids is of little value as it is soft and flows away from the area of contact. Ceramic or metal or alloy lubricants must be used then.

Inorganic solids: Graphite, hexagonal boron nitride, molybdenum disulfide and tungsten disulfide are examples of solid lubricants. Some retain their lubricity to very high temperatures. The use of some such materials is sometimes restricted by their poor resistance to oxidation (e.g., molybdenum disulfide degrades above 350 °C in air, but 1100 °C in reducing environments.

Metal/alloy: Metal alloys, composites and pure metals can be used as grease additives or the sole constituents of sliding surfaces and bearings. Cadmium and Gold are used for plating surfaces which gives them good corrosion resistance and sliding properties, Lead, Tin, Zinc alloys and various Bronze alloys are used as sliding bearings, or their powder can be used to lubricate sliding surfaces alone.

Aqueous lubrication

Aqueous lubrication is of interest in a number of technological applications. Strongly hydrated brush polymers such as PEG can serve as lubricants at liquid solid interfaces. By continuous rapid exchange of bound water with other free water molecules, these polymer films keep the surfaces separated while maintaining a high fluidity at the brush–brush interface at high compressions, thus leading to a very low coefficient of friction.

Biolubricants

Biolubricants are derived from vegetable oils and other renewable sources. They usually are triglyceride esters (fats_ obtained from plants and animals. For lubricant base oil use the vegetable derived materials are preferred. Common ones include high oleic canola oil, castor oil, palm oil, sunflower seed oil and rapeseed oil from vegetable, and Tall oil from tree sources. Many vegetable oils are often hydrolyzed to yield the acids which are subsequently combined selectively to form specialist synthetic esters. Other naturally derived lubricants include lanolin (wool grease, a natural water repellent).

Whale oil was a historically important lubricant, with some uses up to the latter part of the 20th century as a friction modifier additive for automatic transmission fluid.

In 2008, the biolubricant market was around 1% of UK lubricant sales in a total lubricant market of 840,000 tonnes/year.

Functions of lubricants

One of the single largest applications for lubricants, in the form of motor oil, is protecting the internal combustion engines in motor vehicles and powered equipment.

Keep moving parts apart

Lubricants are typically used to separate moving parts in a system. This separation has the benefit of reducing friction and surface fatigue, together with reduced heat generation, operating noise and vibrations. Lubricants achieve this in several ways. The most common is by forming a physical barrier i.e., a thin layer of lubricant separates the moving parts. This is analogous to hydroplaning, the loss of friction observed when a car tire is separated from the road surface by moving through standing water. This is termed hydrodynamic lubrication. In cases of high surface pressures or temperatures, the fluid film is much thinner and some of the forces are transmitted between the surfaces through the lubricant..

Reduce friction

Typically the lubricant-to-surface friction is much less than surface-to-surface friction in a system without any lubrication. Thus use of a lubricant reduces the overall system friction. Reduced friction has the benefit of reducing heat generation and reduced formation of wear particles as well as improved efficiency. Lubricants may contain additives known as friction modifiers that chemically bind to metal surfaces to reduce surface friction even when there is insufficient bulk lubricant present for hydrodynamic lubrication, e.g. protecting the valve train in a car engine at startup.

Transfer heat

Both gas and liquid lubricants can transfer heat. However, liquid lubricants are much more effective on account of their high specific heat capacity. Typically the liquid lubricant is constantly circulated to and from a cooler part of the system, although lubricants may be used to warm as well as to cool when a regulated temperature is required. This circulating flow also determines the amount of heat that is carried away in any given unit of time. High flow systems can carry away a lot of heat and have the additional benefit of reducing the thermal stress on the lubricant. Thus lower cost liquid lubricants may be used. The primary drawback is that high flows typically require larger sumps and bigger cooling units. A secondary drawback is that a high flow system that relies on the flow rate to protect the lubricant from thermal stress is susceptible to catastrophic failure during sudden system shut downs. An automotive oil-cooled turbocharger is a typical example. Turbochargers get red hot during operation and the oil that is cooling them only survives as its residence time in the system is very short (i.e. high flow rate). If the system is shut down suddenly (pulling into a service area after a high-speed drive and stopping the engine) the oil that is in the turbo charger immediately oxidizes and will clog the oil ways with deposits. Over time these deposits can completely block the oil ways, reducing the cooling with the result that the turbo charger experiences total failure, typically with seized bearings. Non-flowing lubricants such as greases and pastes are not effective at heat transfer although they do contribute by reducing the generation of heat in the first place.

Carry away contaminants and debris

Lubricant circulation systems have the benefit of carrying away internally generated debris and external contaminants that get introduced into the system to a filter where they can be removed. Lubricants for machines that regularly generate debris or contaminants such as automotive engines typically contain detergent and dispersant additives to assist in debris and contaminant transport to the filter and removal. Over time the filter will get clogged and require cleaning or replacement, hence the recommendation to change a car's oil filter at the same time as changing the oil. In closed systems such as gear boxes the filter may be supplemented by a magnet to attract any iron fines that get created.

It is apparent that in a circulatory system the oil will only be as clean as the filter can make it, thus it is unfortunate that there are no industry standards by which consumers can readily assess the filtering ability of various automotive filters. Poor filtration significantly reduces the life of the machine (engine) as well as making the system inefficient.

Transmit power

Main article: Hydraulics

Lubricants known as hydraulic fluid are used as the working fluid in hydrostatic power transmission. Hydraulic fluids comprise a large portion of all lubricants produced in the world. The automatic transmission's torque converter is another important application for power transmission with lubricants.

Protect against wear

Lubricants prevent wear by keeping the moving parts apart. Lubricants may also contain anti-wear or extreme pressure additives to boost their performance against wear and fatigue.

Prevent corrosion

Many lubricants are formulated with additives that form chemical bonds with surfaces or that exclude moisture, to prevent corrosion and rust. It reduces corrosion between two metallic surface and avoids contact between these surfaces to avoid immersed corrosion.

Seal for gases

Lubricants will occupy the clearance between moving parts through the capillary force, thus sealing the clearance. This effect can be used to seal pistons and shafts.

Fluid types

• Automotive
  • Engine oils
    • Petrol (Gasolines) engine oils
    • Diesel engine oils
  • Automatic transmission fluid
  • Gearbox fluids
  • Brake fluids
  • Hydraulic fluids
• Tractor (one lubricant for all systems)
  • Universal Tractor Transmission Oil – UTTO
  • Super Tractor Oil Universal – STOU – includes engine
• Other motors
  • 2-stroke engine oils
• Industrial
  • Hydraulic oils
  • Air compressor oils
  • Food Grade lubricants
  • Gas Compressor oils
  • Gear oils
  • Bearing and circulating system oils
  • Refrigerator compressor oils
  • Steam and gas turbine oils
• Aviation
  • Gas turbine engine oils
  • Piston engine oils
• Marine
  • Crosshead cylinder oils
  • Crosshead Crankcase oils
  • Trunk piston engine oils
  • Stern tube lubricants

Other relevant phenomena

"Glaze" formation (high temperature wear)

A further phenomenon that has undergone investigation in relation to high temperature wear prevention and lubrication, is that of a compacted oxide layer glaze formation. Such glazes are generated by sintering a compacted oxide layer. Such glazes are crystalline, in contrast to the amorphous glazes seen in pottery. The required high temperatures arise from metallic surfaces sliding against each other (or a metallic surface against a ceramic surface). Due to the elimination of metallic contact and adhesion by the generation of oxide, friction and wear is reduced. Effectively, such a surface is self-lubricating.

As the "glaze" is already an oxide, it can survive to very high temperatures in air or oxidising environments. However, it is disadvantaged by it being necessary for the base metal (or ceramic) having to undergo some wear first to generate sufficient oxide debris.

Disposal and environmental

It is estimated that 40% of all lubricants are released into the environment. Common Disposal methods include Recycling, burning, landfill and discharge into water, though typically disposal in landfill and discharge into water are strictly regulated in most countries, as even small amount of lubricant can contaminate a large amount of water. Most regulations permit a threshold level of lubricant that may be present in waste streams and companies spend hundreds of millions of dollars annually in treating their waste waters to get to acceptable levels.

Burning the lubricant as fuel, typically to generate electricity, is also governed by regulations mainly on account of the relatively high level of additives present. Burning generates both airborne pollutants and ash rich in toxic materials, mainly heavy metal compounds. Thus lubricant burning takes place in specialized facilities that have incorporated special scrubbers to remove airborne pollutants and have access to landfill sites with permits to handle the toxic ash.

Unfortunately, most lubricant that ends up directly in the environment is due to general public discharging it onto the ground, into drains and directly into landfills as trash. Other direct contamination sources include runoff from roadways, accidental spillages, natural or man-made disasters and pipeline leakages.

Improvement in filtration technologies and processes has now made recycling a viable option (with rising price of base stock and crude oil). Typically various filtration systems remove particulates, additives and oxidation products and recover the base oil. The oil may get refined during the process. This base oil is then treated much the same as virgin base oil however there is considerable reluctance to use recycled oils as they are generally considered inferior. Basestock fractionally vacuum distilled from used lubricants has superior properties to all natural oils, but cost effectiveness depends on many factors. Used lubricant may also be used as refinery feedstock to become part of crude oil. Again there is considerable reluctance to this use as the additives, soot and wear metals will seriously poison/deactivate the critical catalysts in the process. Cost prohibits carrying out both filtration (soot, additives removal) and re-refining (distilling, isomerisation, hydrocrack, etc.) however the primary hindrance to recycling still remains the collection of fluids as refineries need continuous supply in amounts measured in cisterns, rail tanks.

Occasionally, unused lubricant requires disposal. The best course of action in such situations is to return it to the manufacturer where it can be processed as a part of fresh batches.

Environment: Lubricants both fresh and used can cause considerable damage to the environment mainly due to their high potential of serious water pollution. Further the additives typically contained in lubricant can be toxic to flora and fauna. In used fluids the oxidation products can be toxic as well. Lubricant persistence in the environment largely depends upon the base fluid, however if very toxic additives are used they may negatively affect the persistence. Lanolin lubricants are non-toxic making them the environmental alternative which is safe for both users and the environment.

Societies and industry bodies

• American Petroleum Institute (API)
• Society of Tribologists and Lubrication Engineers (STLE)
• National Lubricating Grease Institute (NLGI)
• Society of Automotive Engineers (SAE)
• Independent Lubricant Manufacturer Association (ILMA)
• European Automobile Manufacturers Association (ACEA)
• Japanese Automotive Standards Organization (JASO)
• Petroleum Packaging Council (PPC)

Major publications

• Peer reviewed
  • Tribology Transactions
  • Journal of Synthetic Lubricants
  • Tribology Letters
  • Lubrication Science
• Trade periodicals
  • Tribology and Lubrication Technology
  • Fuels & Lubes International
  • Oiltrends
  • Lubes n’ Greases
  • Compoundings
  • Chemical Market Review
  • Machinery lubrication

See also

• Castor oil
• Grease (lubricant)
• Lubrication
• Mineral oils
• Motor oil
• Oil analysis
• Penetrating oil
• Personal lubricant
• Society of Tribologists and Lubrication Engineers
• Tribology

References

Notes

Sources

• API 1509, Engine Oil Licensing and Certification System, 15th Edition, 2002. Appendix E, API Base Oil Interchangeability Guidelines for Passenger Car Motor Oils and Diesel Engine Oils (revised)
• Boughton and Horvath, 2003, Environmental Assessment of Used Oil Management Methods, Environmental Science and Technology, V38
• I.A. Inman. Compacted Oxide Layer Formation under Conditions of Limited Debris Retention at the Wear Interface during High Temperature Sliding Wear of Superalloys, Ph.D. Thesis (2003), Northumbria University ISBN 1-58112-321-3
• Mercedes-Benz oil recommendations, extracted from factory manuals and personal research
• Measuring reserve alkalinity and evaluation of wear dependence
• Testing used oil quality, list of possible measurements
• Lubricant Additives: Chemistry and Applications, Leslie R. Rudnick, CRC Press.

External links

• SAE-ISO-AGMA viscosity conversion chart
• Chart of API Gravity and Specific gravity

English Journal

• A model system for developing a tissue engineered meniscal enthesis.

• McCorry MC1, Mansfield MM2, Sha X3, Coppola DJ4, Lee JW5, Bonassar LJ6.
• Acta biomaterialia.Acta Biomater.2017 Jul 1;56:110-117. doi: 10.1016/j.actbio.2016.10.040. Epub 2016 Oct 29.
• PMID 27989921

• Continuous monitoring of API content, API distribution and crushing strength after tableting via near-infrared chemical imaging.

• Wahl PR1, Pucher I1, Scheibelhofer O1, Kerschhaggl M2, Sacher S1, Khinast JG3.
• International journal of pharmaceutics.Int J Pharm.2017 Feb 25;518(1-2):130-137. doi: 10.1016/j.ijpharm.2016.12.003. Epub 2016 Dec 5.
• PMID 27923700

• Hyaluronan regulates cell behavior: a potential niche matrix for stem cells.

• Solis MA1, Chen YH, Wong TY, Bittencourt VZ, Lin YC, Huang LL.
• Biochemistry research international.Biochem Res Int.2012;2012:346972. doi: 10.1155/2012/346972. Epub 2012 Feb 12.
• PMID 22400115

Japanese Journal

• ピンポイント噴霧方式による「外部滑沢装置」の紹介 (口腔内崩壊製剤特集号) -- (口腔内崩壊錠と製剤機械技術の進歩)

• 上村 稔
• 製剤機械技術学会誌 = Journal of pharmaceutical machinery and engineering 21(4), 358-364, 2012
• NAID 40019505291

• Development of Electronically Managed Low Speed 4-Stroke Engines

• 岡田 博之,辻岡 幸司,出口 誠,藤本 義光
• マリンエンジニアリング 45(1), 12-17, 2010
• … However, a low speed 4-stroke engine of such kind has not yet been introduced because of its cost-performance relationship.The development of this project has been aimed at improving combustion efficiency, reducing NOx , and minimizing cylinder lubricant dosage rate in a wider operating range not only at the rated power zone but also at the partial load zone, by managing electronically the characteristics of fuel injection, intake and exhaust valve timing and cylinder lubricator control, threrby utilizing the inherent advantages of the 4-stroke engine. …
• NAID 130002569970

• Development of Liposomal Salbutamol Sulfate Dry Powder Inhaler Formulation

• Huang Wen-Hua,Yang Zhi-Jun,Wu Heng [他],Wong Yuen-Fan,Zhao Zhong-Zhen,Liu Liang
• Biological and Pharmaceutical Bulletin 33(3), 512-517, 2010
• … Magnesium stearate (0.5%) was added as a lubricator. … 0.5% magnesium stearate was used as a lubricator. …
• NAID 130000248107

Related Links

• Mechanical lubricator - Wikipedia, the free encyclopedia

A Mechanical lubricator, or automatic lubricator, is a device fitted to a steam engine to supply lubricating oil to the cylinders and, sometimes, the bearings and axle box mountings as well. There are various types of mechanical lubricator.

• Viper Wire Rope Lubricator

Viper Wire Rope Lubricator sales, information and distribution. Contact us on Telephone: +61 2 9636 5655 or Email Sales: sales@viperwrl.com.

Related Pictures