Orthodontic technology is a specialty of dental technology that is concerned with the design and fabrication of dental appliances for the treatment of malocclusions, which may be a result of tooth irregularity, disproportionate jaw relationships, or both.
There are three main types of orthodontic appliances: active, passive and functional. All these types can be fixed or removable.
Contents
- 1 Active Appliances
- 1.1 Removable active appliances
- 1.2 Fixed active appliances
- 2 Passive Appliances
- 2.1 Removable passive appliances
- 2.2 Fixed passive appliances
- 3 Functional appliances
- 3.1 Removable functional appliances
- 3.1.1 Orthodontic Headgear
- 3.1.2 Orthodontic facemask and reverse-pull headgear
- 3.2 Fixed functional appliances
- 4 References
Active Appliances[edit]
An active appliance is a device used to apply forces to the teeth to change the relationship of the teeth.
Removable active appliances[edit]
- Expansion and Labial Segment Alignment Appliance (ELSAA)
Fixed active appliances[edit]
- Pin and tube appliances
- Ribbon arch appliances
- Begg lightwire appliances
- Edgewise appliances
- Pre-adjusted edgewise appliances
- Self-ligating edgewise appliances
- Bi helix
- Tri helix
- Quad Helix
- Rapid Maxillary Expansion appliance (RME)
- Tip-edge appliance
Passive Appliances[edit]
Passive appliances include space maintainers and retainers
Removable passive appliances[edit]
- Hawley retainer
- Begg retainer
- Vacuum formed "Essix" retainer
Fixed passive appliances[edit]
- Bonded "Twistflex" retainer
- Fixed space maintainer
Functional appliances[edit]
A functional appliance is an appliance that produces all or part of its effect by altering the position of the mandible/maxilla. Also known as dentofacial orthopaedic appliances, these appliances utilize the muscle action of the patient to produce orthodontic or orthopaedic forces. Various functional appliances have been described.
Removable functional appliances[edit]
- Andresen Appliance- This is to reduce the overbite, making the molars over-erupt.
- Bionator — Bionators initially look like a sort of combined upper and lower Hawley retainer, but do not fasten to the teeth and are not used for post-brace removal treatment. Bionators are held in the mouth within the space that the teeth surround when biting. They are used to expand the palate and create space for incoming teeth.
- Biobloc — Biobloc is an appliance used to posture forward the lower jaw.
- Clark Twin Block — This appliance incorporates the use of upper and lower bite blocks to position the mandible forward for skeletal Class II correction. The appliance was first developed by Scottish Orthodontist William Clark and Orthodontic Technician James Watt in 1977. The Twin Block has become the most popular functional appliance in use in the United Kingdom and is gaining popularity across Europe and the USA.[citation needed]
- Bass Dynamax — This appliance is similar in principle to the Twin Block. It is based around a prefabricated modular spring, built into a maxillary (upper)occlusal splint. Two integral vertical springs make contact with a fixed lingual arch or removable lower appliance to posture the mandible (lower jaw) forward for skeletal Class II correction. This appliance was developed by London Orthodontist Neville Bass in the early twenty-first century.
- Medium Opening Activator- This is a modified version of the Andreson appliance.
Orthodontic Headgear[edit]
Main article: Orthodontic headgear
Orthodontic Headgear is a type of appliance attached to dental braces that aids in correcting more severe bite problems.
Headgear is an orthodontic appliance for the correction of Class II correction, typically used in growing patients to correct overbites by holding back the growth of the upper jaw, allowing the lower jaw to catch up.
The headgear can also be used to make more space for teeth to come in. The headgear is then attached to the molars (via molar headgear bands & tubes), and helps to push or draw them backwards in the mouth, opening up space for the front teeth to be moved back using braces and bands.
Headgear needs to be worn approximately 12 to 22 hours a day to be truly effective in correcting the overbite, and treatment is usually anywhere from 6 to 18 months in duration, depending on the severity of the overbite and how much a patient is growing.[citation needed]
Orthodontic facemask and reverse-pull headgear[edit]
Main article: Orthodontic headgear
Facemask or Reverse-pull Headgear is used to control the growth of the maxillary and mandibular bones during orthodontic treatment.
The appliance is used in growing patients to correct under bites (known as a Class III orthodontic problem) by pulling forward and assisting the growth of the upper jaw, allowing the upper jaw to catch up.
Facemasks or reverse-pull headgear needs to be worn approximately 12 to 22 hrs to be truly effective in correcting the under bite, usually anywhere from 6 to 18 months depending on the severity of the bite and how much a patient is growing.[citation needed]
The appliance normally consists of a frame or a centre bars that are strapped to the patients head during a fitting appointment. The frame has a section which is positioned in front of the patients mouth, which allows for the attachment of elastic or rubber bands directly into the mouth area. These elastics are then hooked onto the child's braces (brackets and bands) or appliance fitted in his or her mouth.
This creates a forward 'pulling' force to pull the upper jaw forward.
Fixed functional appliances[edit]
- Herbst Appliance: A Herbst Appliance corrects overbites by holding the lower jaw in a protrusive position.[1] It is similar to the Twin Block Appliance except that it is fixed in place and hence non-removable. This appliance is most commonly used in non-compliant patients. The Herbst appliance is very effective in correcting large overbites due to small lower jaws in patients that are growing.[citation needed]
- Fixed Twin Block Appliance: The Twin Block appliance is a removable appliance, and its high comfort level allows you to wear it 24 hours a day. This appliance actually is made up of two separate appliances that work together as one. The upper plate includes an optional expansion screw to widen your upper arch, if needed, as well as pads to cover your molars. The lower plate includes pads to cover your lower bicuspids. These two appliances interlock at an angle, and they move your lower jaw forward and lock it into the ideal position when you bite together. This new position, while temporary, will eventually become the permanent corrected position.[citation needed]
References[edit]
- ^ http://library.thinkquest.org/5029/herbst.htm
|
Orthodontics (ICD-9-CM V3 24.7–24.8, ICD-10-PCS 0C?W–X)
|
|
| Diagnosis |
|
|
| Appliances |
- Archwire
- Braces
- Headgear
- Invisalign
- Elastic ligature
- Palatal expander
- Quad helix
- Retainer
|
|
| Procedures |
- Accelerated orthodontic treatment
- Cantilever mechanics
|
|
| Materials |
- Beta-titanium
- Nickel titanium
- Stainless steel
- Timolium
- Elgiloy
- Ceramic
- Composite
|
|
| Notable contributors |
- Edward Angle
- David Di Biase
- Allan G. Brodie
- Sheldon Friel
- James A. McNamara
- Cecil C. Steiner
|
|
| Other specialties |
- Endodontology
- Periodontology
- Prosthodontology
|
|
| Organizations |
- American Association of Orthodontists
- British Orthodontic Society
- Canadian Association of Orthodontists
- Orthodontic National Group
- Orthodontic Technicians Association
|
|
|
|
|
noco/cong/jaws/tumr, epon, injr
|
dent, proc (endo, orth, pros)
|
|
|
|
|
noco/cofa (c)/cogi/tumr, sysi
|
|
|
|
|